Maxwell Render

Maxwell Render Information Repository
It is currently Fri May 24, 2013 1:59 am

View unanswered posts | View active topics


Board index » Plugins Support » Maxwell for Solidworks

All times are UTC + 1 hour [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
John Layne
 Post subject: 2.7 Bugs
PostPosted: Tue Jun 19, 2012 6:59 am 
User avatar

Joined: Tue Apr 19, 2005 10:35 pm
Posts: 325
Location: Auckland New Zealand
1/ Mirrored parts moving even with instances turned off.
2/ If add-in is turned off then on again, the Maxwell tab goes blank. Only way to restore is to check "start-up" on the Maxwell add-in and restart SolidWorks. Note I normally have the Maxwell add-in turned off, due to instability issues in SolidWorks when it's on.

_________________
John Layne

http://www.solidengineering.co.nz

"The mass of men lead lives of quiet desperation"
Henry David Thoreau 1854
Top
 Profile  
 
JDHill
 Post subject: Re: 2.7 Bugs
PostPosted: Tue Jun 19, 2012 5:19 pm 
User avatar

Joined: Wed Nov 16, 2005 3:02 am
Posts: 7578
Location: desk #861
    1. Could you please elaborate, or provide a SW file that I can inspect? I am not yet seeing the problem here.

    2. I see this, but don't know that there is anything I can do about it. Basically, once you disable, then re-enable the plugin, its task pane UI ceases to function correctly. But I'll check it out some more and see if there are any tricks I'm missing. As to instabilities, I would need some more detail there too -- it could be that there is a bug triggered in a certain set of circumstances, of which I am not currently aware.

_________________
Next Limit Team
Top
 Profile  
 
John Layne
 Post subject: Re: 2.7 Bugs
PostPosted: Wed Jun 20, 2012 9:51 am 
User avatar

Joined: Tue Apr 19, 2005 10:35 pm
Posts: 325
Location: Auckland New Zealand
JDHill wrote:
    1. Could you please elaborate, or provide a SW file that I can inspect? I am not yet seeing the problem here.


    2. I see this, but don't know that there is anything I can do about it. Basically, once you disable, then re-enable the plugin, its task pane UI ceases to function correctly. But I'll check it out some more and see if there are any tricks I'm missing..
Can't post or email to big, do you have a dropbox account or similar? Was working ok in previous add-in --- I used to disable and re-enable it all the time. Instability issue was hard to pin down, hence just found it easier to disable the add-in when not using.

_________________
John Layne

http://www.solidengineering.co.nz

"The mass of men lead lives of quiet desperation"
Henry David Thoreau 1854
Top
 Profile  
 
JDHill
 Post subject: Re: 2.7 Bugs
PostPosted: Wed Jun 20, 2012 2:42 pm 
User avatar

Joined: Wed Nov 16, 2005 3:02 am
Posts: 7578
Location: desk #861
I'll follow up via email.

_________________
Next Limit Team
Top
 Profile  
 
JDHill
 Post subject: Re: 2.7 Bugs
PostPosted: Fri Jul 27, 2012 3:43 pm 
User avatar

Joined: Wed Nov 16, 2005 3:02 am
Posts: 7578
Location: desk #861
Hi John, please check these two things again with the 2.7.10 plugin -- both should be fixed.

_________________
Next Limit Team
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Plugins Support » Maxwell for Solidworks

All times are UTC + 1 hour [ DST ]

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group